Cosa dovrei fare nel caso in cui Sika®Cleaner G+P si ghiacci?
  • Spostare la lavorazione in un luogo più caldo
  • Pulire il vetro in magazzino prima di lasciare l'officina per l'installazione mobile
  • Eseguire una pulizia a secco della linea di incollaggio con Sika®Cleaner PCA
Posted on: 08/05/2019
Perchè usare Sika® Cleaner G+P al posto di alcool o dei comuni pulitori per vetro in commercio
  • L'alcool può reagire con il poliuretano e bloccare i gruppi reattivi, inficiando l'indurimento e lo sviluppo dell'adesione.
Posted on: 08/05/2019
Vi è la possibilità di diluire Sika® Cleaner G+P?
  • Si sconsiglia di diluire i prodotti chimici in quanto la compatibilità non è garantita e la composizione è stata sviluppata per ottenere i migliori risultati.
Posted on: 08/05/2019
Per quanto tempo Primers e Aktivators sono attivi dopo l'apertura?
  • Tutti i Sika Aktivators e Primers riducono la loro durata una volta aperti. Mantenendo delle condizioni di stoccaggio adeguate, questi rimangono utilizzabili per 2-4 setimane (vedere PDS) dopo l'apertura, o fino alla data di scadenza, nel caso arrivasse prima. Richiudere saldamente sempre entrambi i tappi dopo ogni uso. Se il prodotto incrementa la sua viscosità o in caso diventi opaco, o inomogeneo, scartare immediatamente la confezione in accordo con quanto riportato sulla Scheda di Sicurezza.
Posted on: 08/05/2019
Sika® Aktivator PRO può essere usato in condizioni di elevata umidità?
  • Si, Sika® Aktivator PRO può essere sato in condizioni di elevata umidità, es. su parabrezza con una leggera formazione di condensa. (In questo caso, ‘elevata umidità’ si riferisce a condizioni umide dove NON sono visibili grandi gocce d'acqua, ristagni di condensa o gocce di pioggia). Comunque, è meglio asciugare la parte prima.
Posted on: 08/05/2019
If the open time of Sika® Aktivator PRO has passed, is it ok to perform the activation step again?
  • Yes. It is OK to apply Sika® Aktivator PRO up to three times onto the bonding surface. It is important that the surface is clean and activated. You can tell if the surface has been activated when it has a shimmery aspect to it. If you are uncertain it is better to re-apply Sika® Aktivator PRO.  
Posted on: 08/05/2019
Why is the use of daubers with Sika® Aktivator PRO not recommended?
  • Sika® Aktivator PRO performs a cleaning function, as well as an activating function. Application with a dauber simply moves dirt around and does not clean it off. Daubers apply too much product, which is unnecessary and wasteful.
  • They can become dirty and contaminate the activator if they are dipped in the bottle several times.
Posted on: 08/05/2019
Why does Sika®Primer-207 need to be shaken?
  • Shaking primers mixes the solids that may have settled at the bottom of the bottle and ensures a thin, uniform mixture and coverage. All manufacturer’s primers containing solids should be shaken before use.
Posted on: 08/05/2019
Can I dilute high viscous/gelled Sika®Primer-207?
  • If the viscosity of the primer gets high, NEVER use thinners or solvents to dilute the product as the higher viscosity is an indication of lower reactivity.
Posted on: 08/05/2019
What happens if too thick a layer of Sika® Primer-207 is applied?
  • Applying a thick layer of Sika® Primer-207 results in a longer flash-off time. But if applied as corrosion protection on bare metal it is recommended that two thick layers of Sika® Primer-207 be applied for long lasting protection
Posted on: 08/05/2019
Is there a product for cleaning Sika® Primer-207 from interior parts?
  • Sika® Primer-207 can be cleaned using Sika® Remover-208 or Sika® Handwipes tissues as long as it has not cured completely. Once cured, it must be removed mechanically.
Posted on: 08/05/2019
Are there any aggressive components in Sika® Aktivator PRO or Sika® Primer-207 that could attack surfaces?
  • Sika® Aktivator PRO and Sika® Primer-207 contain reactive components which react chemically with glass, paint and other materials. Once cured, they can only be removed mechanically and the upper layer of the substrate is damaged in the process. Care must be taken to apply Sika® Aktivator PRO only to the required areas. If the product is applied to the transparent area of the glass, it will be visible and the customer will have cause for complaint.
Posted on: 08/05/2019
Can Sika®Primer-207 be used to imitate a ceramic frit on float glass for UV protection?
  • To ensure a durable bond, transparent windshields must be surface-protected against UV. Sika® UV Shielding Tape or trims can be used in cases where no protection is given. Sika Primer (and most glass primers from other manufacturers) are organic materials and will be destroyed by UV radiation within a very short time and therefor provide no durable protection.

Possible solutions are:

  • Suitable print color.
  • Protective metal or opaque plastic trim
  • .Sika® UV Shielding Tape.
Posted on: 08/05/2019
What is the minimum temperature to perform a replacement job?
  • Sika’s products are intended for use at temperatures between +5°C and +35°C. For all other conditions Sika has special hot and cold weather recommendations. While a job can be carried out at -10°C, there is a question of adequate dexterity with cold hands. It may be too cold to carry out the job to a suitable professional standard. In this case, the job should be deferred.
Posted on: 08/05/2019
How long do I need to wait to wash my car after windscreen replacement?
  • Soaps and cleaning helps can influence the curing negatively and frameless glasses are sensitive to water pressure and air dryer as they could damage the fresh skin of the urethane, therefore a waiting time of 24h is needed (not needed if installed with Powercure System)
Posted on: 08/05/2019
Having cut out a windshield, the old PUR bead contained lots of small bubbles in the adhesive bead. How can this be prevented?
  • The PUR adhesive releases carbon dioxide while curing. If the adhesive bead is heated during curing, the gas is released more quickly which can result in small bubbles dispersed throughout the bead. This can happen if the car is parked with the windshield exposed to sunlight on a warm day. Parking the car in the shade will prevent this problem.
Posted on: 08/05/2019
How to bond a windscreen to a FRP bodies structure?
  • If the old PU is still in place the standard procedure can be followed
  • If you bond directly to FRP use abrasive pad to scuff the surface, Sika®Cleaner G+P to and apply Sika®Primer-207
Posted on: 08/05/2019
How to bond a freshly painted vehicle?
  • New paints are difficult to bond as they are developed to be self-cleaning and repellent
  • Allow the paint to properly cure first (24h)
  • Use abrasive pad to scuff the surface, Sika®Cleaner G+P to clean and apply Sika®Primer-207
Posted on: 08/05/2019
Why does the primer not wet the surface properly?
  • If the surface tension of a substrate is insufficient the primer will show wetting issues on the surface. This is mostly known from non-traditional contaminations present on ceramic frits.
  • Remove and clean (Sika®Cleaner PCA), or use glass fit for purpose.
Posted on: 08/05/2019
The surface shows after cleaning with Sika®Cleaner PCA still wetting issues
  • The use of dry Sika®Cleaner PCA increases cleaning efficiency as the glass cleaner can act as a lubricant.
Posted on: 08/05/2019